STT | Ứng dụng | Thông số | Chú thích |
1 | reset biến tần về mặc định | parameter group list = all | File management=>Factory settings =>Parameter group list = all |
2 | thời gian tăng tốc | Acceleration = | Simply start=> simply start=> acceleration |
3 | thời gian giảm tốc | Deceleration = | Simply start=> simply start=> Deceleration |
4 | tần số thấp | Low Speed = | Simply start => Simply start=> low speed |
5 | tần số max | high speed | Simply start => Simply start=> high speed |
6 | đảo chiều động cơ | DI2 = Reverse | Complete settings=>Input/Output=>DI2 = Reverse |
7 | cài đặt rơ le phanh đèn báo chạy dừng | r1 assignment = Driver running | Complete settings=>Input/Output=>R1 configuration =>r1 assignment= Driver running |
8 | chức năng dừng tự do | Type of stop= freewheel stop | Complete settings=>Generic functions=>Stop configuration =>type of stop=freewheel stop |
9 | cấu hình analog biến tần | AI1 Type = voltage,current | Complete settings=>Input/Output =>AI1 configuration=>AI1 Type= |
10 | bù momen động cơ | IR compensation=150% | Complete settings=>Motor parameters=>IR compensation=150% |
11 | điều chỉnh tần số sóng mang giảm tiếng ồn động cơ | switching frequency= 7khz motor noise = yes | Complete settings=>Motor parameters =>Switching frequency =?; motor noise = yes |
12 | chế độ điều khiển 3 dây | 3-Wire Control | Simply start=>Simply start=>2/3-wire control=>3-Wire Control or complete settings=>input/output=> 3-wire |
13 | cài đặt bật nguồn lên chạy ngay khi đang có lệnh chạy | 2-wire type = Level With Fwd Priority | Complete settings=>Input/Output =>2-wire type= Level With Fwd Priority |
14 | chế độ điều khiển riêng biệt (ktra trên mặt và bàn phím) | control mode = separate mode | Complete setting => Command and Reference => control mode => separate |
15 | Đặt tần số trên mặt biến tần | Ref Freq Config = Ref. Freq.Term (LCC) | Complete setting => Command and Reference => Ref Freq Config |
16 | kích hoạt lệnh chạy trên bàn phím cmd channel 1 = Terminals | | Complete setting => Cmd channel 1= terminals |
17 | cho phép chạy trên mặt biến tần | cmd channel 1 = Ref.Freq-Rmt.Term | Complete setting => Command and Reference => cmd channel 1 |
18 | chạy chuyển kênh | ref freq1 config = AI2 | cài lại, chú thích rõ ràng |
19 | Command switching=cmd channel 1 |
20 | cmd channel 1 = terminal |
21 | cmd channel 2 = terminal |
22 | freq switch assign = di3 |
23 | ref freq 2 config = AI1 |
24 | chạy thay thế khi DI1 bị hỏng | reverse assignment= di4, di5, di6 | complete setting=>input/output=> reverse assignment = di4, di5, di6 |
24 | chạy nhiều cấp tốc độ | Complete settings=>Generic functions=>Preset speeds | on/off biến tần LI1 (mặc định) |
25 | 2 preset Freq = DI2 | low speed cấp tốc độ thứ nhất |
26 | 4 preset Freq = DI3 | LI2(2 cấp tốc độ) |
27 | 8 preset Freq = DI4 | LI3 (4 cấp tốc độ) |
28 | 16 preset Freq = DI5 | LI4 (8 cấp tốc độ) |
29 | preset speed 2… preset speed 16 | lần lượt các cấp tốc độ từ 2 đến 8 |
30 | | 'Simply start => Simply start=> low speed | tốc độ đầu tiên đặt tần số trên bàn phím |
31 | PID | PID Feedback: | |
32 | AI1 type=current | tín hiệu phản hồi về dòng |
33 | AI1 min.value=4 mA(theo cảm biến) | dòng phản hồi về min |
34 | AI1 max.value=20 mA(theo cảm biến) | dòng phản hồi về max |
35 | Min Pid Feedback = 0bar | |
36 | Max Pid Feedback = 10bar | |
37 | pid reference: | |
38 | Ref Freq 1 config = Ref.Freq-Fmt.Term | cài tần số tham chiếu nội. |
39 | Intern pid ref = yes | cho phép cài tần số tham chiếu nội |
40 | Internal PID ref = 5 bar | tần số đặt tham chiếu nội (setpoint) |
41 | Min PID reference = 0 bar( theo cảm biến) | |
42 | max PID reference = 10 bar(theo cảm biến) | |
43 | Pid settings | |
44 | PID prop.Gain = 1(khâu p) | kp |
45 | pid integral.gain = 1(khâu I) | ki |
46 | CHẾ ĐỘ NGỦ, THỨC PID | Complete settings=>Generic functions=>sleep/wake up | sleep/wake up |
47 | sleep menu | |
48 | sleep detect mode = speed | cho phép chế độ ngủ |
49 | sleep delay = 35 s | thời gian trễ cho biến tần ngủ |
| sleep min speed = 35hz | tần số thấp cho biến tần ngủ |
51 | wake up pressure | |
52 | wake up process = 4 bar | áp suất thức dậy của biến tần |
53 | wake up Delay: 5s | thời gian trễ để biến tần thức dậy |